Within the realm of FPV, choosing the proper flight controller stack to your FPV drone may be pivotal. Enter the GEPRC Taker F405 50A FC/ESC stack, a budget-friendly choice for low price builds. This evaluate dives into its specs and options to see the way it stacks up towards the Speedybee F405 V4.
Study extra about FPV drone flight controllers in our purchaser’s information: https://oscarliang.com/flight-controller-explained/
The place to Purchase?
Get the GEPRC Taker F405 stack from these distributors:
Unboxing the GEPRC Taker F405, I discovered a complete set of equipment:
- 1x 35V 1000uF capacitor
- 1x DJI Air Unit Adapter Cable
- 1x Flight Controller Adapter Cable
- 1x XT60 Energy cable (14AWG)
- 4x M3x30 Screws
- 4x M3x24 Screws
- 8x Nylon nuts
- 8x Silicone grommets
- 2x sh1.0 4pinsilicone cable
- 1x Digital camera connection cable
Specs
GEP-F405-HD V2 Flight Controller
- MCU: STM32F405
- IMU: ICM42688-P (SPI)
- Air Unit Connection: Direct plugging into DJI Air Unit
- Black Field: 16M onboard
- USB Connector: Sort-C
- OSD: BetaFlight OSD w/ AT7456E chip
- BEC: 5V,9V twin BEC
- Firmware Goal: GEPRCF405
- Measurement: 36.8×36.8mm, gap 30.5×30.5mm,φ4mm gap turns into φ3mm after utilizing a silicone shock-absorbing circle.
- Enter Voltage: 3-6S LiPo
- UART: 6
- Energy Filter: Built-in LC filter
- Weight: 7.7g
GEP-BLS50A-4IN1Â ESC
- Enter Voltage: 3-6S Lipo
- Galvanometer: Help
- Steady Present: 50A
- Burst Present: 55A(5s)
- Help Protocol: Oneshot125/Oneshot42/Mulishot modes/Dshot 150/300/600
- Measurement: 42.9×39.7mm, hole30.5×30.5mm,φ4mm gap turns into φ3mm after utilizing the silicone shock-absorbing circle.
- Weight:13.7g
- Goal: G_H_30
Pinout Diagram
Standout Options
At $64, the GEPRC Taker F405 is $2 cheaper than the Speedybee F405 V4 – one other standard finances choice, but doesn’t skimp on performance. Its versatile design, that includes each solder pads and connectors just like the RushFPV F722 V2, caters to varied preferences, whether or not you’re in search of a fast swap functionality or direct soldering.
The provision of connectors for HD VTX’s (appropriate with DJI Air Unit and Walksnail VTX), GPS, Receiver and FPV digicam, makes it appropriate for various drone builds together with freestyle and lengthy vary.
The GEPRC Taker F405 helps Betaflight in addition to iNav – the iNav 7.0 goal identify is GEPRCF405.
Limitations and Issues
It will have been extra user-friendly in the event that they put the connectors on the underside, and the solder pads on high. The solder pads are fairly small, which makes soldering a bit difficult particularly for these much less skilled.
Whereas the Taker F405 matches lots of the Speedybee F405 V4’s specs – similar processor, gyro and variety of UART’s, its lack of a barometer might disappoint these eager on utilizing GPS Rescue Mode.
The ESC doesn’t have a heatsink for cooling and bodily safety just like the Speedybee F405 V4 stack.
Apparently, the Taker F405 stack was launched again in summer season 2023 (over 6 months now), however not a single evaluate on the market. The dearth of dialogue about this product raises questions on its long-term reliability, so solely time will inform.
The 9V BEC on this FC has a barely decrease ranking at 2.5A than the Speedybee V4’s 3A. Not an enormous distinction however one thing to contemplate.
There’s no Bluetooth on the Taker both – not a difficulty in case you solely configure your flight controller by way of USB port. However for these favor altering settings wirelessly from the Speedybee App on their telephone, this may be a deal breaker.