The BetaFPV Pavo35 is the largest of the Pavo cinewhoop sequence. It’s a flexible 6S drone that stands out within the FPV market. With its sturdy construct and bigger propellers, it’s designed for extra demanding cinematography duties.
Study extra about Cinewhoops: https://oscarliang.com/cinewhoop/
The place to Purchase?
Get the Pavo35 from these distributors:
Only a Larger Pavo25 V2?
The Pavo35 and Pavo25 V2 share quite a lot of similarities when it comes to {hardware}, however cater to completely different flying types and wishes.
Left: Pavo25 V2; Mid: Pavo35; Proper: Pavo20
The principle distinction is within the body measurement, props measurement and motor measurement, the remaining are virtually the identical. Word that the Pavo35 has the XT60 mounted within the entrance whereas the Pavo25 V2 has the XT30 mounted within the again.
Specification
- FC: F722 35A AIO V2
- Motor: LAVA Collection 2006 Brushless Motors
- Propellers: GemFan D90S 3-Blade Propellers(1.5mm Shaft)
- Battery: LAVA Collection 6S 1100mAh LiPo Battery
- VTX: DJI O3 Air Unit, Walksnail Avatar HD Professional Equipment, Caddx Vista Equipment, RUNCAM Hyperlink, Analog
Specs comparability between Pavo35 and Pavo25 V2:
| Pavo25 V2 | Pavo35 | |
| Wheelbase | 112mm | 148mm |
| Motor | 1505 4600KV | 2006 2400KV |
| Props | GF D63-3 | GF D90S-3 |
| Battery Connector | Mounted XT30 | Mounted XT60 |
| Weight w/o O3 & LiPo | 153g | 238g |
| Weight with O3 & LiPo | 190g | 274g |
| Battery | 4S 650-850mAh | 6S 1050-1400mAh |
| Flight Time | 6~8 minutes | 10~12 minutes |
| Advocate Digital camera | Bare GoPro, Insta Go3 | GoPro12, DJI Action4 |
| FC | F722 35A AIO V2 | |
| Help VTX | DJI O3, Walksnail, Runcam Hyperlink, Analog | |
| Help Digital camera | DJI O3, Any micro cameras (19mm width) | |
| RX Model | ELRS, TBS | |
| Digital camera Mount | GoPro Mount | |
PAVO25 v2: The Compact 4S Flyer
The PAVO25 v2 is smaller, designed for 4S batteries, and very best for carrying lighter motion cameras. It’s an amazing alternative if you happen to’re in search of a compact, easy-to-carry drone. Its specs embody:
- Wheelbase: 112 mm
- Motors: 1505 4600 kv
- Weight: 153g (with out FPV battery)
- Flight time: 6-8 minutes
- Appropriate cameras: Bare GoPro, Insta360 Go 2 and Go 3, Caddx Peanut, Runcam Thumb Professional
PAVO35: Energy and Versatility
In distinction, the PAVO35 is constructed for extra sturdy efficiency, working on 6S batteries. It’s able to carrying full-size GoPros, making it good for extra demanding filming duties. Key options embody:
- Wheelbase: 148 mm
- Motors: 2006 2400 kv
- Weight: 238g (dry)
- Flight time: 10-12 minutes
- Suitable with full-size motion cameras like GoPro Hero 12
Frequent Options
Each fashions function:
- F722 35A AIO flight controller
- COB LED mild strips
- Choices for ExpressLRS or TBS receivers
- Excessive thrust-to-weight ratio
- Y-shaped CNC metallic help for elevated structural power
Design and Construct High quality
Weighing round 274g (with ELRS receiver and DJI O3), the Pavo35 is significantly lighter in comparison with the GepRC Cinelog35. It includes a slimmer battery strap and low-profile antenna, contributing to its smooth design.
It comes with a mount for a full-size GoPro digital camera, and makes use of rubber grommets for digital camera vibration isolation, very same components used within the Cinelog25 V2.
The Pavo35 boasts a 3mm high plate and bigger, extra sturdy prop guards in comparison with the smaller Pavos. The aluminum standoffs add to its sturdiness.
One regarding space is the XT60 connector soldering level, which is completely uncovered. It’s proper subsequent to the propellers, any moist grass/leaf/particles might simply brief the battery connection. I’d strongly advocate conformal coating it earlier than flying exterior: https://oscarliang.com/waterproofing-drone-electronics/
Elements
As talked about, the Pavo35 makes use of the identical FC/ESC board because the smaller Pavo25 V2. It’s powered by an F722 35A AIO V2 flight controller, which features a 4-in-1 35A ESC, 6 UARTs, a connector for simply connecting a DJI or Walksnail digital FPV system, a micro USB connector, a 16MB Blackbox. It is available in variations with no radio receiver, with a 2.4GHz ExpressLRS or Crossfire Nano RX receiver.
It’s outfitted with 2006 2400KV motors and Gemfan D90S three-blade propellers, which in line with BetaFPV present energy similar to that of a 5-inch racer. It’s very best for carrying heavier masses like full-size GoPros.
Whereas some cinewhoops this measurement are utilizing 22xx sizes, I feel 2006 is a superb alternative for a lighter setup. It’s supposed for a smaller battery to maintain the load down. You would possibly get much less flight time, however it gives you the flexibility to fly extra aggressively. 22xx motor measurement will enable for bigger batteries and end in longer flight time, nevertheless it limits agility and the pilot could be pressured to fly extra clean and regular.
One in all my major criticism could be battery mounting. When carrying a heavy GoPro within the entrance, the battery strap location is mounted within the center, which limits how a lot you possibly can transfer the battery to the again. That leads to a entrance heavy drone and impacts efficiency.
Putting in DJI O3
The DJI O3 Air Unit is meant to be put in below the flight controller, contained in the prop guard. No must solder, simply plug it in with the cable offered by BetaFPV. It simple to disassemble the Pavo35, there are 4 screws to take away the underside plate the place the O3 is put in.
Disconnect the digital camera module and antenna from the O3 Air Unit first. Set up the digital camera and antenna within the quad.
Sadly, the wires of the O3 antenna appear too brief for the Pavo35. Ultimately I needed to reduce the plastic tube brief so I can push the antenna down to permit the wires to succeed in the Air Unit.
Then join the digital camera and antenna to the O3, earlier than mounting it to the underside plate.
Putting in the O3 is comparatively easy, although accessing the micro SD card and USB-C port on the DJI O3 is hard because of the design of the ducts.
Flying Expertise
BetaFPV suggests 6S batteries from 1000 to 1500mAh with an XT60 connector, making it appropriate for high-speed outside flying. With a 6S 1100mah LiPo, the quad weighs 465g.
With a 6S 1100mah LiPo and Gopro Hero 11, the Pavo35 weighs 620g, hovers at about 28% throttle, it feels very responsive and highly effective. It additionally feels noticeably extra highly effective than the Speedybee Bee35 I not too long ago examined, to the purpose that the Pavo35 with GoPro onboard feels just like the Bee35 with out GoPro. The sunshine weight of the quad performs an enormous half.
Nonetheless the Pavo shouldn’t be as environment friendly because the Bee35, flight time is about 1 minute shorter, at round 4 minutes, it’s nowhere close to the 8-minute mark claimed by BetaFPV. You would possibly get longer flight time if you happen to don’t do any flips and rolls and simply cruise. However for most individuals it’s nonetheless loads for some nice cinematic pictures. You possibly can undoubtedly use a bigger battery for longer flight time, though that may make it heavier and fewer agile.
The PAVO35’s efficiency is commendable each indoors and outside. When flying indoors, it’s clean although you would possibly wish to tilt the digital camera down as a result of it’s a bit too highly effective. Flying outside is the place it actually shines, and I feel it’s potential for chasing fast-paced topics like motorbikes.
Learn how to Setup
The FC has a micro USB connector, which is hidden contained in the body. I can barely entry it with a small cable with out taking the drone aside.
The firmware is Betaflight model 4.4.2. Board goal is BETAFPVF722. Discover unique CLI dump right here: https://intofpv.com/t-cli-dump-for-betafpv-pavo35-original
BetaFPV took care of many of the settings: the two UARTs for the DJI O3 Air Unit (or an Avatar VTX) and the ELRS receiver – so there are 4 UART’s left obtainable. PIDs and charges are manufacturing facility set.
The ExpressLRS receiver is simple to bind, comply with one among these strategies: https://oscarliang.com/bind-expresslrs-receivers/. If you should flash RX firmware, the receiver is a BETAFPV 2.4GHz Nano RX. What’s barely disappointing, is the truth that by plugging within the FC USB cable, it doesn’t energy the receiver. So to bind or take a look at receiver, you’d should plug within the Lipo battery.
All that continues to be is to setup Modes tab in Betaflight Configurator – the switches for arming, the flight modes, the Flip Over After Crash, the beeper. Comply with this information to be taught extra: https://oscarliang.com/betafliaght-modes/
Conclusion
The BetaFPV PAVO35 6S Cinewhoop is a superb alternative for these looking for a cinewhoop that’s highly effective sufficient to hold a full measurement GoPro digital camera whereas nonetheless delivers spectacular pace and agility. It’s well-suited for each indoor cinematic pictures and outside high-speed pursuits, making it a flexible possibility in your FPV arsenal.
Get the Pavo35 from these distributors:
Nonetheless, it appears BetaFPV’s method to the Pavo35 differed from their typical meticulous design course of seen in different fashions of the Pavo sequence. It seems extra like a easy upscaled model of the Pavo25 V2, with bigger motors and propellers. Regardless of its commendable flight efficiency, I consider there’s room for enchancment in sure design facets to spice up the person expertise and general reliability. However, for these in pursuit of a high-performance, light-weight, and agile 3.5″ cinewhoop, the Pavo35 emerges as a powerful competitor, particularly when it comes to its flying capabilities.
